Xantech IR Emitters
282M
Single Non-Visible IR Emitter |
|
|---|
- Non visible (blinks only infrared light) high output version.
- New deep purple Lexan® shell.
- New and improved clear adhesive film included on emitter housing for attachment to IR window of controlled component.
- Two 1/2" pieces of double-sided clear adhesive tape included for replacement purposes.
- Lead is terminated with a 3.5mm mono mini plug.
- Length of wire: 10 feet.
- Instruction Manual (PDF)
| |
This series of mini emitters contain a tiny infrared light emitting diode housed in a miniature, almost black, injection molded plastic shell. These versatile units can be used in a number of innovative ways.
They are designed to be installed directly on the IR control window of the controlled equipment. The almost black shell passes infrared (IR) leaving access to the original remote controller while at the same time making the most unobtrusive installation possible.
The new mouse emitters are made of a deep purple Lexan® for improved infrared pass-through, allowing a greater range of direct control of components from hand-held controllers. The “M” series emitters also now use a new and improved adhesive that keeps emitters attached to components in even the most harsh conditions.
| |
|
283M
Single Visible IR Emitter |
|
|---|
- Visible (blinks infrared and visible light) lower output version.
- New deep purple Lexan® shell.
- New and improved clear adhesive film included on emitter housing for attachment to IR window of controlled component.
- Two 1/2" pieces of double-sided clear adhesive tape included for replacement purposes.
- Lead is terminated with a 3.5mm mono mini plug.
- Length of wire: 10 feet.
- Instruction Manual (PDF)
| |
This series of mini emitters contain a tiny infrared light emitting diode housed in a miniature, almost black, injection molded plastic shell. These versatile units can be used in a number of innovative ways.
They are designed to be installed directly on the IR control window of the controlled equipment. The almost black shell passes infrared (IR) leaving access to the original remote controller while at the same time making the most unobtrusive installation possible.
The new mouse emitters are made of a deep purple Lexan® for improved infrared pass-through, allowing a greater range of direct control of components from hand-held controllers. The “M” series emitters also now use a new and improved adhesive that keeps emitters attached to components in even the most harsh conditions.
| |
|
284M
Double Non-Visible IR Emitter |
|
|---|
- Two emitters on a single plug!
- Non visible (blinks only infrared light) high output version.
- New deep purple Lexan® shell.
- New and improved clear adhesive film included on emitter housing for attachment to IR window of controlled component.
- Spare double-sided clear adhesive tape included for replacement purposes.
- Lead is terminated with a 3.5mm mono mini plug.
- Length of wire: 7 feet to junction, 3 feet to each emitter.
- Instruction Manual (PDF)
| |
This series of mini emitters contain a tiny infrared light emitting diode housed in a miniature, almost black, injection molded plastic shell. These versatile units can be used in a number of innovative ways.
They are designed to be installed directly on the IR control window of the controlled equipment. The almost black shell passes infrared (IR) leaving access to the original remote controller while at the same time making the most unobtrusive installation possible.
The new mouse emitters are made of a deep purple Lexan® for improved infrared pass-through, allowing a greater range of direct control of components from hand-held controllers. The “M” series emitters also now use a new and improved adhesive that keeps emitters attached to components in even the most harsh conditions.
| |
|
286M
Dual Visible IR Emitter |
|
|---|
- Two emitters with a single plug!
- Visible (blinks infrared and visible light) lower output version.
- New deep purple Lexan® shell.
- New and improved clear adhesive film included on emitter housing for attachment to IR window of controlled component.
- Two 1/2" pieces of double-sided clear adhesive tape included for replacement purposes.
- Lead is terminated with a 3.5mm mono mini plug.
- Length of wire: 10 feet.
- Instruction Manual (PDF)
| |
This series of mini emitters contain a tiny infrared light emitting diode housed in a miniature, almost black, injection molded plastic shell. These versatile units can be used in a number of innovative ways.
They are designed to be installed directly on the IR control window of the controlled equipment. The almost black shell passes infrared (IR) leaving access to the original remote controller while at the same time making the most unobtrusive installation possible.
The new mouse emitters are made of a deep purple Lexan® for improved infrared pass-through, allowing a greater range of direct control of components from hand-held controllers. The “M” series emitters also now use a new and improved adhesive that keeps emitters attached to components in even the most harsh conditions.
| |
|
282TP
TWIN PLUG MOUSE EMITTER
|
|
|---|
- 282M high-output Mouse Emitter with two 3.5mm plugs
- Allows control of single source by two IR systems
- Diode isolation for independent control and component protection
- Wire length: 10 feet
- Note: The 282 Emmiter does not blink when it recives an IR code. The 283 Does.
| |
|
380-20
J-box IR Blaster
|
|
|---|
- Powerful transmitter can send IR signal across rooms
- Mounts in a standard J-box
- Unit contains 3 high-current IR LED's
| |
Back by popular demand, the Blast-IR returns! This J-box mounted unit
is designed to send an IR signal great distances, allowing for simplified
installation in situations where running wires to equipment is undesirable.
| |
|
282X
NO SHELL EMITTER
|
|
|---|
- 282M high-output Mouse Emitter with no shell surrounding
emitter head
- Allows insertion of emitter inside component case for the
cleanest appearance possible
- Wire length: 10 feet
| |
|
|
